Introduction Stainless steel Super Duplex 2507 is designed to handle highly corrosive conditions and situations were high strength is required. High molybdenum, chromium and nitrogen content in Super Duplex 2507 help the material withstand pitting and crevice corrosion. The material is also resistant to chloride stress corrosion cracking, to erosion corrosion, to corrosion fatigue, to general corrosion in acids. This alloy has good weldability and very high mechanical strength. The following sections will discuss in detail about stainless steel grade Super Duplex 2507. Chemical Composition The chemical composition of stainless steel grade Super Duplex 2507 is outlined in the following table. Element | Content (%) | Chromium, Cr | 24 - 26 | Nickel, Ni | 6 - 8 | Molybdenum, Mo | 3 - 5 | Manganese, Mn | 1.20 max | Silicon, Si | 0.80 max | Copper, Cu | 0.50 max | Nitrogen, N | 0.24 - 0.32 | Phosphorous, P | 0.035 max | Carbon, C | 0.030 max | Sulfur, S | 0.020 max | Iron, Fe | Balance | Physical Properties The physical properties of stainless steel grade Super Duplex 2507 are tabulated below. Properties | Metric | Imperial | Density | 7.8 g/cm3 | 0.281 lb/in3 | Melting point | 1350°C | 2460°F | Applications Super Duplex 2507 is widely used in the following sectors: Power Marine Chemical Pulp and paper Petrochemical Water desalinization Oil and gas production Products made using Super Duplex 2507 include: Fans Wire Fittings Cargo tanks Water heaters Storage vessels Hydraulic piping Heat exchangers Hot water tanks Spiral wound gaskets Lifting and pulley equipment Propellers, rotors, and shafts Stock Form | Specification | Supply Form | Others | Sheet | Thickness:0.40-4.75mm,General Width:1000,1219,1500mm | Whole Coil or piece of it | Cold Annealed,Surface 2B,2E | Plate | Thickness:4.76-60mm,Width:1500,2000,2500mm,Length:3000,6000,8000,8500mm(Under 10mm plate can be coiled) | Whole Coil or piece of it | Single hot rolling,Solid solution annealed state,Surface 1D | Belt | Thickness:0.10-3.0mm,Width:50-500mm | Whole Coil or Specified size | Cold Annealed,Surface 2B,2E | Bar & Rod | Rolled barΦ5-45mm,Length≤1500mm | Polished Bar(circle,Square) | Solution annealing,descaling | Forged barΦ26-245mm,Length≤4000mm | Weld tube | Outer diameterΦ4.76-135mm,Wall Thickness0.25-4.00mm,Length:≤35000 mm | Base on your requirement | Use for PHE | Seamless Tube | Outer diameterΦ3-114mm,Wall Thickness0.2-4.5mm | Base on your requirement | Use for PHE | Wire | Outer diameterΦ0.1-13mm | Base on your requirement | Ni & Ni Alloy, Ti & Ti Alloy | Forged piece | roundness and square alloy | Base on your requirement | Steel, Alloy | Flangs | All kinds of Flangs | Base on your requirement | Steel, Alloy | Welding Material | Coil wire Φ0.90mm/1.2mm/1.6mm | Base on your requirement | Certificate of Origin:America, Sweden, Britain, Germany, Austria, Italy, France. | Straight WireΦ1.2mm/1.6mm/2.4mm/3.2mm/4.0mm | Welding rodΦ2.4mm/3.2mm/4.0mm | Tube | Elbow, three links, four links, different diameter size | Base on your requirement | Ni & Ni alloy, Ti & Ti alloy | Explosive bonded laminate | Raw Sheet Thickness≥2mm | Base on your requirement | Ni & Ni alloy, Ti & Ti alloy | Contact us if you need more details on 2207 Stainless Steel Pipe. We are ready to answer your questions on packaging, logistics, certification or any other aspects about Steel Tube、Stainless Steel Tube. If these products fail to match your need, please contact us and we would like to provide relevant information. Product Categories : Stainless Steel > Stainless Steel Pipe
|